Changed the board and new serial cable, exact same random shut down. Changed the push unit in addition to new upper board. Exact challenge. What is going on right here as not anything else to interchange? Is there a compatability situation With all the more mature intellitouch i7 as Pentair denies this?

1000RR claimed: Great to know about the vinegar too, which makes total feeling. I'd listened to/go through before that executing acid washes can reduce the everyday living. Is always that Because it requires a toll over the blade materials them selves? Click to grow...

So mainly it's looking through all-around 50 degrees +/-5 now. Then when it goes for getting out from the diagnostic method, it goes straight to your pink light for Cold Water Cutoff. Werid. So I try and go diagnostic manner all over again and also the IC40 reboots generally likely into startup method While using the red and green lights blinking for your salt... then when It truly is performed It's going to get started operating appropriately. If I go back to diagnostic method, It will do the very same regime as outlined above.

Then it went bacl to "Chilly" with Ability light-weight ON and Building flashing inexperienced (no other lights). and reverted to those readings. The temp suggests sixty three now, but the water is actually 72:

Howdy , This thread is inactive for over 60 times. New postings here are not likely to generally be found or responded to by other users. For superior visibility, look at Starting off A different Thread.

Nov seven, 2024 Increase bookmark #fourteen well a tech arrived out and it is a bad upper board exactly where the Serial port sits. Negative out in the box! Now working on a fresh MasterTemp heater set up that does not want to communicate whatsoever to my Intellitouch.

Mike1162 mentioned: I just viewed a online video on youtube that shows them inside a laundry bag currently being positioned right into a washing equipment. Do the Instructions point out this? Click to broaden...

Newdude mentioned: Yeah. The acid strips the Ruthium coating which makes the magic transpire and the cells say proper on them to wash them each individual three months.

There are two main reasons why you would probably want To do that. 1 is your tub incorporates an surplus quantity of natural and organic squander, and is applying massive a...

I current it to become far more apparent than prior to. It had all the things in there but maybe it wasn't very clear it absolutely was all Pentair?!

From working day a single (when we acquired your home a month ago), it (Intellichlor/ScreenLogic) has not indicated salt degree (on my ScreenLogic, it's generally shown ZERO). But no lights around the chlorinator were being indicating lower salt or some other concerns (at first). My chlorine stage was floating close to 10ppm And that i experienced my chlorinator set to 0% but it had been holding at nine-10ppm regularly (instead of decreasing over time as I might foresee). So all alongside I have been Feel the chlorinator was producing [slightly] chlorine Despite the fact that I'd it set to 0%. But staying new towards the SWG pools plus the Pentair tools, I assumed I'd wait around and find out what it did. Nicely, a couple of 7 days ago I recognized that the crimson light-weight (around the IC40) was on (was not before) to the Chilly Water Cutoff. I went in on the diagnostic manner from the device and it reads forty% (4000 hrs) to the life/utilization and Once i'd strike the up button again to view what temp it absolutely was reading, no lights would arrive on for temp. Immediately after a couple of days (from the Crimson Gentle with the Cold Water Cutoff), my chlorine amounts started dropping (so it absolutely was definitely not creating chlorine any more). So soon after some investigate, I was certain it had been a the circulation/temp sensor. I ordered two of these figuring They are really recognized to go out and I would have a spare. I replaced the sensor and initially, on startup, I saw a salt studying on my ScreenLogic cellphone App of 4600 (my real salt degree is about stahlwandpool 150 tief 3500-3600).

No joy, I’m frightened. Tentatively got in tonight for twenty five minutes and was itching just before I went to bed. Little bumps on my skin in random areas that push me nuts.

Area a good-bodyweight painter's tarp (material or polymer) or hefty blanket above the gear pad. Some may even location one or two contractor/painter lamps with 100W incandescent bulbs underneath the tarp for heat.

Comply with combined with the video clip below to see how to setup our web page as an internet app on your house screen. Be aware: This function is probably not readily available in a few browsers.